How to Clean, Dry, Patch and Store a Bounce House
How to clean a bounce house, dry it so it does not mildew, patch small holes, fold it and store it, from the Little Tikes and Bounceland manuals.

Affiliate disclosure: product links on this page go to Amazon, or to the maker's own store for brands that sell only direct. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you; a link to a maker's store earns us nothing. No retailer or brand sees our picks before they are published or has any say in them. How we choose.
Wipe a bounce house down with a cloth and a mild, non-toxic cleaner or plain water, let it dry completely while inflated, then deflate it, fold it in half three times, roll it up from the end opposite the inflation tube, and store it indoors. The one rule every manual repeats is the one that saves the bouncer: never pack it away wet. Bounceland's warranty does not cover mold or mildew from improper storage.
Cleaning
What the makers say to use
- Little Tikes: wipe the bouncer with a dry cloth, or a cloth dampened with a neutral, non-flammable, non-toxic cleaning and sanitizing solution, or pure water.
- Bounceland: wipe clean with a mild detergent, and keep water away from the blower at all times.
Neither maker mentions pressure washers, bleach or solvents, and both want the blower kept dry. Little Tikes says not to immerse the blower in water and to wipe it with a damp cloth; XPOWER, which makes replacement blowers, says never clean its blower with water.
Step by step
- Get everyone out and sweep out leaves, grass and toys while it is still inflated.
- Wipe the floor, walls and slide with your cloth and cleaner, working from the top down.
- Rinse the cloth often; wipe again with plain water if your cleaner leaves a film.
- Leave the blower running so the bouncer stays inflated while it dries.
Vinyl (commercial) units are easier: HeroKiddo and JumpOrange describe their vinyl as a smooth, non-porous surface that wipes clean between events. Nylon and Oxford bouncers hold dirt in the weave, so expect to wipe more than once.
Drying
This is the step that decides whether the bouncer comes out of storage in spring. Little Tikes says the product should never be stored wet and to allow it to dry before rolling it up. Bounceland says do not store it wet, and its warranty excludes mold and mildew from improper storage. Banzai's water park manual warns of mildew if it is stored damp.
- Dry it inflated, in the sun or a breeze, with the blower running.
- Check seams, corners, the underside and any water pockets on steps; Little Tikes says to remove water and debris from pocket steps after each play cycle.
- If it rained or you used it wet, give it the time it needs; packing it at dusk to beat the dew defeats the point.
How long is long enough? Banzai's manual says to let its water park dry completely before rolling it up, which may take up to 48 hours. EPA's guide to mold and moisture gives the outer limit for anything that got wet: dry it within 24 to 48 hours to prevent mold growth. If the forecast will not give you a dry day, inflate it again in a garage or on a covered patio and run the blower until it is dry, then pack it.
Bouncers with water bags
Some bouncers use water-filled weight bags instead of, or as well as, stakes. Bounceland's instructions: detach the water bags, move the bouncer and blower away before you open the drain valve, empty the bags and let them dry in a cool place before they go in the bag with everything else.
Patching small holes
Most bouncers ship with patches. Little Tikes' method:
- Deflate the bouncer, clean the area and let it dry thoroughly.
- Cut the patch to size and round the corners.
- Peel the backing, place the patch over the damage and smooth out any bubbles.
- Wait 30 minutes before inflating again.
Little Tikes adds that patches must be applied by an adult and kept away from children. Bounceland says its patches suit the laminated PVC areas, such as the jumping surface, and other areas can be stitched by hand with a needle and strong household thread. Do not try to seal the seams: air escaping through them is how a constant-air bouncer is designed to work.
For replacement patches, match the patch to the material. Tear-Aid's own FAQ says Type A is for canvas, nylon and most fabrics, and warns not to use Type A on vinyl, because oils in vinyl will in time turn the Type A adhesive gooey and lift it off. Type B is for vinyl and vinyl-coated surfaces only. Only Type B can go on a wet surface, and Tear-Aid says even that works better dry. Most residential bouncers are coated nylon or Oxford polyester, so Type A fits them; commercial units are PVC vinyl and need Type B.
For commercial vinyl units, use Tear-Aid Type B or a vinyl patch kit such as Magic Jump's.
Deflating and folding
Bounceland's method, which suits most residential bouncers:
- Turn the blower off, unplug it, and detach the inflation tube. Bounceland says the bouncer deflates on its own within 5 minutes.
- Remove the stakes by their heads, not by tugging the loops; see anchors and sandbags.
- Fold the bouncer in half, then in half two more times, parallel to the first fold.
- Roll it up tightly from the end opposite the inflation tube, pressing air out as you go. Little Tikes' diagrams show the same: compress the air out as you roll.
- Slide the carry bag over the roll and zip it.
Little Tikes notes the product is heavy; lift with care, and do not drag it across concrete or rough ground, which both Little Tikes and Bounceland warn against.
If you find mold
Spots of mildew on a bouncer that went away damp are common enough that Bounceland writes mold and mildew from improper storage out of its warranty. EPA's advice for mold at home is to scrub it off hard surfaces with detergent and water and dry them completely, and it warns that absorbent or porous materials may have to be thrown away if they become moldy. A smooth vinyl unit behaves like a hard surface. A nylon or Oxford bouncer is a woven fabric that holds moisture in the weave, so scrub and dry it, and if the mold keeps coming back or the fabric smells after drying, stop using it and ask the maker.
Storing
- Indoors and dry. Bounceland says store the bouncer and blower indoors in dry conditions; the Bouncing Angels manual says a low-humidity indoor room.
- Not in a damp basement. EPA recommends keeping indoor humidity below 60 percent, ideally 30 to 50 percent; a room that damp in summer will not stay dry for a folded bouncer.
- Blower upright. Little Tikes says store the blower indoors, upright on a stable surface, with the cord loosely coiled beside it.
- Check before next use. Inspect for tears, weak seams and mold, and the blower for damaged cords, before the first party of the season. Every manual says not to use a unit with damage until it is repaired.
What each manual says
| Source | Clean with | Drying | Storage |
|---|---|---|---|
| Little Tikes | Dry cloth, or neutral, non-flammable, non-toxic cleaner, or pure water | Never store wet; dry before rolling up | Blower indoors, upright, cord loosely coiled |
| Bounceland | Mild detergent; water away from the blower | Do not store wet; never leave outside in rain | Bouncer and blower indoors, dry |
| Bouncing Angels (commercial) | Disinfectant cleaner on the floor and inside | Water units: drain, run empty until dry, hand dry with soft towels before deflating | Clean, dry, low-humidity indoor room; never outside |
| Banzai (water park) | Keep pool and slide free of dirt and leaves | Dry completely; up to 48 hours | Rolled, after drying |
Common mistakes
- Packing it damp after a wet day. The fastest way to mildew.
- Hosing the blower. Wipe it; keep it dry.
- Patching a seam. Seams leak by design.
- Leaving it out overnight. Bounceland says not to leave it inflated overnight, and dew undoes the drying.
For setup rules, see bounce house safety rules; if the blower is the part that failed, see our blower guide.
Frequently asked questions
How do you clean a bounce house?
Wipe it while inflated with a cloth and a mild, non-toxic cleaner or plain water. Little Tikes specifies a neutral, non-flammable, non-toxic cleaning and sanitizing solution or pure water; Bounceland says a mild detergent. Keep water away from the blower.
How do you dry a bounce house?
Leave it inflated with the blower running, in sun or a breeze, until every seam, corner and step pocket is dry. Little Tikes and Bounceland both say never store it wet.
Can you pressure wash a bounce house?
The Little Tikes and Bounceland manuals only describe wiping with a cloth and a mild cleaner or water. Stick to that, and never spray the blower; Little Tikes says not to immerse it in water.
How do you patch a hole in a bounce house?
Deflate, clean and dry the area, cut the patch with rounded corners, press it on and smooth out bubbles, then wait 30 minutes before inflating, per Little Tikes. Bounceland says non-vinyl areas can be stitched by hand with strong thread.
How do you get mold off a bounce house?
EPA says to scrub mold off hard surfaces with detergent and water and dry them completely, and that porous materials may have to be thrown away if they become moldy. Vinyl wipes clean like a hard surface; a woven nylon or Oxford bouncer holds moisture, so if mold returns after scrubbing and drying, contact the maker. Bounceland's warranty does not cover mold from improper storage.
How do you fold a bounce house to store it?
Fold it in half, then in half twice more parallel to the first fold, and roll it tightly from the end opposite the inflation tube, pressing air out, per Bounceland. Then slide the bag over the roll.
Where should you store a bounce house over winter?
Indoors in a dry, low-humidity room, with the blower upright and its cord loosely coiled, per Little Tikes, Bounceland and the Bouncing Angels manual. Inspect it for damage and mold before the next use.
Sources
- Jr. Jump 'n Slide Bouncer: Instructions for Installation and Operation (637995), Little Tikes
- Bounceland Owner's Manual and Safety Guidelines, Bounceland
- Warranty, Bounceland
- Owner's Manual: Inflatable Castle Style Bouncer 13x13 ft, Bouncing Angels
- Speed Slide Water Park: Instructions, Banzai
- XPOWER High Static Blower Owner's Manual, Models BR-272A, BR-282A, BR-292A, XPOWER Manufacture
- A Brief Guide to Mold, Moisture and Your Home, U.S. Environmental Protection Agency
- Frequently Asked Questions, Tear-Aid
Cover image: Illustration: Backyard Inflatable Review (AI-generated)
Related guides
Best Bounce House Blowers: Replacement and Commercial (2026)
Five inflatable blowers from 5.5 to 11.5 amps, and why the horsepower on the box is the least useful number on it.
Bounce House Anchors: Stakes, Sandbags and Wind Limits
Stakes, sandbags and tarps for bounce houses and water slides, and the wind speeds at which Little Tikes, Bounceland and CPSC say to stop.
Bounce House Safety Rules: Setup, Supervision and Water
The rules every bounce house manual repeats, plus what CPSC and Nationwide Children's Hospital add, in one checklist you can print for the party.


